terça-feira, 23 de abril de 2013

Boeing 787 Battery - New Kit for Repairing All Fleet Batteries


Teams of Boeing engineers and technicians began fanning out across the globe on Monday to modify the battery systems of the company’s 50 grounded 787 Dreamliner jets to expedite getting the planes back in the air.
The kits include a new steel containment box for the battery, a new venting system, battery chargers, wiring and other associated hardware built by Boeing itself. Modified batteries, which include better insulation between the cells, are to be shipped separately to the airlines by GS Yuasa, the Japanese maker of the original batteries used in the 787.
Each modification kit should take about five days to install.


Equipes de engenheiros da Beoing e técnicos começaram se espalhando através do globo na Segunda-feira (22) para dodificar os sistemas de bacteria dos 50  jatos Boeing Dreamliner no solo para acelerar colocar de volta  os aviões no ar.

 Os kits incluem uma nova caixa recepiente de aço para a bacteria, um novo sistema de ventilação, carregadores de bacteria, fiação e outros hardware associados construidos pels própria Boeing. Baterias modificadas, as quais incluem isolamento melhor entre as células, estão para serem embarcadas separadamente para as empresas aéreas pel GS Yuasa, a fabricante japonesa das baterias originais usadas no Boeing 787.
Cada kit de modificação deve levar cerca de cinco dias para instalação.





segunda-feira, 15 de abril de 2013

Boeing 737's Horizontal Stabilizer Must Be Scrutinized



FAA: This AD is effective May 20, 2013.

We are adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by reports of an incorrect procedure used to apply the wear and corrosion protective surface coating to attach pins of the horizontal stabilizer rear spar. This AD requires inspecting to determine the part number of the attach pins of the horizontal stabilizer rear spar, and replacing certain attach pins with new, improved attach pins. We are issuing this AD to prevent premature failure of the attach pins, which could cause reduced structural integrity of the horizontal stabilizer to fuselage attachment, resulting in loss of control of the airplane.
 

We estimate that this AD affects 1,050 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Estimated Costs
Action
Labor cost
Parts cost
Cost per product
Cost on U.S. operators
Inspection and attach pin replacement
39 work-hours × $85 per hour = $3,315
Up to $6,312
$9,627
Up to $10,108,350.

According to the manufacturer, some of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate.

 Applicability

(1) This AD applies to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes, certificated in any category.

(2) Installation of Supplemental Type Certificate (STC) ST00830SE (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/408E012E008616A7862578880060456C?OpenDocument&Highlight=st00830se) does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST00830SE is installed, a “change in product” alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17. For all other AMOC requests, the operator must request approval for an AMOC in accordance with the procedures specified in paragraph (k) of this AD.

 

Unsafe Condition

This AD was prompted by reports of an incorrect procedure used to apply the wear and corrosion protective surface coating to attach pins of the horizontal stabilizer rear spar. We are issuing this AD to prevent premature failure of the attach pins, which could cause reduced structural integrity of the horizontal stabilizer to fuselage attachment, resulting in loss of control of the airplane.

Part Number (P/N) Inspection

For airplanes having line numbers 1 through 3534 inclusive: Before the accumulation of 56,000 total flight cycles, or within 3,000 flight cycles after the effective date of this AD, whichever occurs later, inspect to determine the part number of the attach pins of the horizontal stabilizer rear spar. A review of airplane maintenance records is acceptable in lieu of this inspection if the part number of the attach pin can be conclusively determined from that review.
 

Replacement

If, during the inspection required by paragraph (g) of this AD, any horizontal stabilizer rear spar attach pin has P/N 180A1612-3 or 180A1612-4, prior to the accumulation of 56,000 total flight cycles on the pin, or within 3,000 flight cycles after the effective date of this AD, whichever occurs later, replace with a new attach pin having P/N 180A1612-7 or 180A1612-8, respectively, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 737-55-1093, dated April 9, 2012.